The Rolled Plate Material window ( Modeling )

Tip:Detail Submaterial can generate an unrolled surface template of a rolled plate material in its submaterial detail.
  • When a legacy miscellaneous member is first added, Add [Legacy] Miscellaneous Member options are shown on this window.
Once a legacy miscellaneous member is added, these options are shown on the [Legacy] Miscellaneous Member Edit window -- and they will no longer be shown on this window.

Also see :

page 1 | contents | adding a rolled plate material or legacy miscellaneous member | top

" Copy " " Paste " " Save " " Load " buttons :

  • You'll find buttons like these at the top of this window. They apply to all user-editable settings (except " Piecemark ") that are on this window. Click here for more information.
  • You can " Copy " ( ) the settings on this window, then " Paste " ( ) those settings to a different rolled plate.
  • " Save " ( ) saves a "form" file to the form/rolled-plate folder that is used by your current version of this program. Give the form a name that will help other users identify its purpose. " Load " ( ) copies over all settings on this window (except " Piecemark ") with the settings that are stored in the file that you select.
  • " Paste " and " Load " replace mixed entries to a single field with a single entry. " Copy " and " Save " ignore fields with mixed entries, treating them as if they have no entry or do not exist. Special cases: Form buttons do not operate on " Piecemark " or "ABM Options .""

page 1 | contents | adding a rolled plate material or legacy miscellaneous member | top

------ General settings ------

Defaults: If you press " OK " to close this window, the entries made to " Material thickness ," " Steel grade ," " Centered ," " Surface finish " and " Color " become the defaults for the next-added rolled plate.

Piecemark: Blank or any character string (up to 61 characters). This is the submaterial piecemark .

If this field is left ' blank ', then when this material is generated (after you press " OK "), SDS2 piecemarking looks for materials in the current Job that are physically identical to this material and assigns to this material the same mark assigned to those materials. If no matching materials are found, the material is assigned a piecemark using the appropriate material mark prefix listed for " Plate " in Home > Project Settings > Fabricator > Member and Material Piecemarking > the " Prefixes " tab.

Any ' character string ' that you enter must be unique. Validation does not let you enter a piecemark that has already been assigned to materials. If you are adding a rolled plate material or legacy miscellaneous member, a piecemark entered here only applies if the material you are adding is unique -- if the material is exactly the same as previously added materials, the new material gets the piecemark of those previously added materials. On the other hand, if you are editing the material, all materials that are exactly like the material are re-assigned the unique mark you enter when the material is generated (after you press " OK "). The piecemark you enter remains a system piecemark , which means that it may be changed if you later edit a material just like this one and give that material a different piecemark.

Tip: If you want to change a submaterial mark, you should use Rename Project Items in Utility Options . That way all references to the submaterial mark are changed throughout the your current Job, even in Drawing Editor drawings.

Note 1: A submaterial mark is not yet assigned when this window opens for an add material or add legacy miscellaneous member operation. A piecemark is shown when you Edit Material or Review 2D Items . For the current quantity of materials assigned this piecemark, see the " Current quantity " listed on this material's General Information window.

Note 2: Two rolled plates may have the same submaterial mark , but different submaterial mark index numbers , if one plate is " Centered " and the other is not.

Report Writer: MemberMaterial.Material.MinorMark
Advanced Selection: MinorMark
Parametric module: MinorMark

Material thickness: The thickness of this rolled plate (in the primary dimension " Units " or other units or the gage ). The thickness of a " Checkered " plate is measured exclusive of its raised pattern, along its Z material axis .

To enter gage plate: Type the ' gage number' followed by ' ga ' (example: ' 4ga ' is rewritten as ' 4GA ' when you Tab out of the field). Right-click tells you the stored thickness (based on industry standards), from which the weight of the gage plate is calculated. Allowable gages are any whole number from 3 to 38 . You can also enter an exact decimal thickness to get the gage (example: ' .1345 ' becomes ' 10GA ' when you Tab out of the field). The " Description " for a gage plate follows the format: ' plate prefix ' + ' numberGA ' + ' x ' + ' width ' (example: PL16GAx15 1/2 ).

Thickness precision : You can enter a plate " Material thickness " that is more precise than the " Dimension precision " that is set at Home > Project Settings > Fabricator > Detailing > Drawing Presentaton . For example, if you enter ' 5/32 ' and the " Dimension precision " is ' 1/16 ', the thickness of the plate will be ' 5/32 '. The thickness you enter will be reflected in the " Description " and will propagate to the bill of material, reports, etc. The setup option to " Round flat plate values " does not affect this. Be aware that the Ruler measures to whatever the " Dimension precision " is set to, which means that the plate's measured thickness may not exactly match its actual thickness.

Status Display: Material status > Material plate thickness
Report Writer: XXXXX . Thickness
Advanced Selection: Thickness
Parametric module: Thickness

Unrolled width: Read-only . This tells you the width of the material when it is layed flat (unrolled). The " Unrolled width " is in the primary dimension " Units ".

The " Unrolled width " is calculated from the rolled plate's " Outside radius " and " Included angle " in accordance with the choice made to " Rolled plate width dimension taken from " at Home > Project Settings > Fabricator > Detailing > Dimension Settings > the " Miscellaneous " tab. The " Unrolled width " is used in the material " Description " found on the General Information window and in the " Description " in the member bill of material. The " Unrolled width " of the plate is also included in the plate section callout on the plate's submaterial detail .

Report Writer: XXXXX . Width
Advanced Selection: Width
Parametric module: Width

Material length: The length (in the primary dimension " Units " or other units ) of the rolled plate along its longitudinal axis ( X material axis ).

Changing the material length results in the difference being added to/subtracted from the end of the rolled plate that is opposite to the first work point that was located. Doing this will also change the " Work point distance " accordingly. If the only operations you are performing on this material are defining an " Outside radius " and an " Included angle ," the distance entered here will be the same as the " Work point distance ."

Report Writer: XXXXX . OrderLength
Advanced Selection: OrderLength or PartLength
Parametric module: OrderLength or PartLength

Work point distance: The distance (in the primary dimension " Units " or other units ) between the work points of this rolled plate.

Note: In most cases, this distance is the same as the " Material length ," and changing the " Work point distance " works in exactly the same way as changing the " Material length ." However, in the case of a tapered rolled plate (where a value for " Outside tapered radius " has been entered), this distance and the " Material length " will be different.

Report Writer: XXXXX . WorkpointSlopeDistance
Advanced Selection: WorkpointSlopeDistance
Parametric module: WorkpointSlopeDistance

Outside radius: The distance (in the primary dimension " Units " or other units ) from the outside corner the rolled plate to the center of an imaginary circle extrapolated from the outside edges of the rolled plate. This distance must be measured at the end of the rolled plate where the first work point that was located if the " Outside tapered radius " results in a taper.

Visualizing the outside radius: Imagine you are looking at the end of the rolled plate where the first work point was located; you would see a cross-section of the width of the rolled plate (its Y material axis ). Extrapolate an arc from the outside curvature of the bend on the rolled plate, then measure the distance from either end of that arc to the center of the imaginary circle which that arc is a part of.

Note: Making a change to the " Outside radius " will directly affect the " Unrolled width " of the rolled plate.

Report Writer: XXXXX . RollOrBendRadius

Outside tapered radius: A distance (in the primary dimension " Units " or other units ) specifying the radius of the rolled plate from the end opposite to where the first work point was located.

The ' exact same distance ' as the " Outside radius " makes the rolled plate not tapered .

A ' distance ' other than that entered to " Outside radius " makes the rolled plate tapered. " Outside tapered radius " works the same way as " Outside radius ," except that this distance is measured from the end of the rolled plate opposite to where the first work point was located.

Report Writer: XXXXX . TaperRadius
Advanced Selection: TaperRadius
Parametric module: TaperRadius

Included angle: Any angle from .1 to 360 degrees.

This is the number of degrees of the circle that is taken up by the arc of the outside face of the rolled plate (the radius of this arc is the " Outside radius "). The entry you make here directly affects the " Unrolled width " of the rolled plate.

Report Writer: XXXXX . RolledOrBentAngle

Fabrication method: Continuous rolling or Segmented bending .

' Continuous rolling ' sets the curve of the rolled plate to be smooth, continuous and parabolic.

' Segmented bending ' causes the rolled plate to be a series of flat (not-curved) bend segments that together approximate a parabola. The number of segments is the number entered to " Bend segments ."

Bend segments: 0 or a quantity of segments from 3 to 400 .

' 0 ' (zero) produces the same result as " Continuous rolling ."

An entry of ' 3 or greater ' applies when " Segmented rolling " is selected. The more the segments, the smaller the bend angle between each segment, and the more closely the rolled plate approximates a continuous parabolic curve.

Steel grade: A36 or A572 or etc. This is the grade of steel of the rolled plate whose settings are defined on this window.

Setup: If the steel grade you want is not on the list box ( ) for this field, you can use Home > Project Settings > Job > Plate Grades to add it to the list.

Tip: Changing " Steel grade " " Color " and " Surface finish " do not cause the plate to be regenerated. This means that, if you change those settings only, material cut operations such as a Cut Layout may, optionally, be preserved.

Report Writer: MemberMaterial.Material.SubMaterial.MaterialGradeDescription
Advanced Selection: MaterialGrade
Parametric module: MaterialGrade

Surface finish: None or Sandblasted or Red oxide or Yellow zinc or Gray oxide or Blued steel or Galvanized or Duplex Coating or Undefined 1 or Undefined 2 or Undefined 3 or Red oxide 2 or Any user added surface finish. This affects the colors of 'Solid ' members on erection views in the Drawing Editor . This also sets the color when "Output material color " is set to 'Surface finish ' for a VRML Export or a DWG/DXF Export . The "Color " ( not "Surface finish ") sets the color of this material in Modeling .

sand blasted red oxide yellow zinc user surface finish 1
gray oxide blued steel galvanized user surface finish 2

To assign a different surface finish, you can drop-down the current surface finish and select the one you want, or you can press the "file cabinet" browse button ( ) and double-click any surface finish that is on the list.

Auto or .

If this box is checked ( ), the material surface finish follows what is set on the member level.

If the box is not checked ( ), the material surface finish can be changed to whatever is available in the list of surface finishes. If the surface finish changes from what the member level has set, the auto checkbox will be unchecked automatically. When the auto check box is unchecked, the member edit window shows an information tag which notifies the user that an attached material is not following what was set on the member level.

Note 1: Submaterial piecemarks can be split apart by surface finish. All surface finishes that do not have the 'Break Marks Material' checked on can be applied to any like material with out the material splitting. If the 'Break Marks Material' is checked on then only like materials with that specific surface finish can have the same piecemark, and because the submaterial marks differ so would the member's piecemark.

Note 2:When exporting a KISS file using "model" as the "Data source " surface finish data on the materials are compiled into the KISS download as follows, with a few exceptions (G=galvanized, N= none or sandblasted, P= others). Those exceptions are:

  • If the box for "Finish" routing in KISS export setup is set to a user routing

  • If the user has adjusted the Abbreviation for any of the default provided surface finishes

  • If you are using a user added surface finish

In these cases you will get what is provided in either the User routing, or the abbreviation field. For other exports it will always provide the abbreviation in the 'surface finishes' settings page.

Tip 1: "Surface area" is reported on the General Information window -- and this can be used to estimate the amount of coating required and its cost.

Tip 2: Changing "Steel grade " "Color " and "Surface finish " do not cause the plate to be regenerated. This means that, if you change those settings only, material fit operations such as a Fit Exact may, optionally, be preserved.

Report Writer:MemberMaterial.Material.SurfaceFinish
Setup:Surface Finish Settings

Color: A predefined color or a Custom Color . This is the approximate color of the rolled plate when it is displayed in one of the three solid forms .

The predefined colors are set up on the Predefined Colors window. The color swatch next to the list box ( ) displays the color that is selected.

Select ' Custom Color ' (last choice on the list) to launch your operating system's color picker and define any color you like.

Please note: Different colors may be assigned to materials that have the same submaterial piecemark . Changing a material's color does not trigger the material to be regenerated.

Report Writer: MemberMaterial.Material.MaterialColor3dRed
Report Writer: MemberMaterial.Material.MaterialColor3dGreen
Report Writer: MemberMaterial.Material.MaterialColor3dBlue

Checkered: or .

If this box is checked ( ), this rolled plate becomes a checkered plate, which is a steel plate with raised ribs on its near-side surface to prevent slippage on items such as floors and stair treads. The " Material thickness " of a checkered plate is measured exclusive of the raised pattern. The prefix set for " Checkered " in Member and Material Piecemarking is applied to the " Description " on the General Information window and in the member bill of material ( example: PL3/8x10 becomes CHPL3/8x10 when ' CH ' is the prefix and it is set to " Append ... ." It becomes CH3/8x10 when not set to " Append... "). The " Weight of item " increases per Table 1-23 ( AISC Thirteenth Edition , p1-87) and also depends on whether " Shop bill weight based on material " is set to ' Volume ' or ' Dimensions '. The plate will be detailed on the submaterial and the member with a small sample of the checkered pattern .

If the box is not checked ( ), the rolled plate is considered to have a smooth near-side surface.

Report Writer: XXXXX . CheckeredPlatePattern
Advanced Selection: CheckeredPlatePattern
Parametric module: CheckeredPlatePattern

Centered: or . This option positions the rolled plate with respect to the first work point located when this rolled plate was added.

If this box is checked ( ), the rolled plate will be positioned so that point 1 is at the vertex of the outside radii of the rolled plate.

If the box is not checked ( ), the rolled plate will be positioned so that point 1 is the material's most outside point.

Piecemarking: Two rolled plates -- one " Centered ," the other not " Centered " -- may have the same submaterial " Piecemark " . The two plates will have different submaterial mark index numbers .

----------------------

  Special Buttons for Detailing this Material
(these do not appear for Add operations)
 
This button opens a window with a list of preset views . Each preset view that you select on this list is drawn on the submaterial detail when you Detail Submaterial . This button opens a list of views you can delete. If the material has only one view, you get a warning instead of a list of views since you cannot delete the current view.  This button does a Detail Submaterial on this material. Newly added views are drawn on the detail. Deleted views are not drawn.

page 1 | contents | adding a rolled plate material or legacy miscellaneous member | top

To close this window :

       

" General Information " opens the General Information window, which provides additional information and settings that pertain to this rolled plate.

Tip: You can use the General Information window to change the material's " X ," " Y ," or " Z " global coordinates (and thus reposition the material within the 3D model).

Also: A " Properties " button at the bottom of the General Information window lets you Edit Properties for this material.

"OK" (or the Enter key) closes this window and applies the settings on it to the material(s).

Defaults: Even if you did not make any changes on this window, pressing " OK " causes certain " General settings " to be applied as the defaults for the next rolled plate that is added in your current session of Modeling .

If this window opened for adding a material or a legacy miscellaneous member, you can still press " Cancel " on the Rotate Material window to end the add operation (see step 4 ).

If you opened this window to edit a single rolled plate ( single-edit ), the Change All Options & Warning List opens after you press " OK ." You can use that window to cancel your changes or, if other materials with the same submaterial piecemark exist, apply your changes to those other materials.

If you opened this window to edit multiple rolled plates ( multi-edit ), the Change All Options & Warning List does not open after you press the " OK " button.

"Cancel" (or the Esc key or the button) closes this window without saving any changes made to it.

Possibilities: If you are adding a new material or a legacy miscellaneous member, " Cancel " brings you back to the work point location step ( step 2 ) in the add operation. For an edit material operation, " Cancel " ends the operation.

"Reset" undoes all changes made to this window since you first opened it. The window remains open.

Note: The settings shown on this window when it first opens for the adding of a material or legacy miscellaneous member are the settings of the last-added or last-edited rolled plate (unless you exit Modeling in the meantime).

"Clear" fills out this window with default settings. These same defaults are applied when the first new rolled plate is added during a session of Modeling in which no other rolled plate has been edited. For example, " Clear " automatically selects the default " Steel grade " and zeros out the " Material thickness ." It also unchecks the box for " Centered ."

Note: The " Clear " button can be used when adding material or a legacy miscellaneous member. It is disabled during an Edit Material operation.

page 1 | contents | adding a rolled plate material or legacy miscellaneous member | top