Narrow Gage OSL All-Bolted Clip Angles ( Fabricator Settings ) (read-only)
Specifications for getting this type of standard clip angle in the model :
.
- Narrow Gage OSL All-Bolted Clip Angles are double clip angles that shop bolt to the supported or supporting member and are designed as the supported beam's end connection when ' Narrow Gage ', ' Bolted ' (to supported), ' Bolted ' (to supporting), ' Both ' (sides of web) and shop attach to ' Supported ' (or ' Supporting ') are set in "
Connection specifications " for auto standard , user defined or beam-window-specified clip angles.
home > project settings > fabricator > pIecemarking > | clip configurations
To open this window :
Method 1 : Home > Project Settings > Fabricator > Piecemarking > All Bolted Clip Angles > Narrow Gage OSL All-Bolted Clip Angles .
home > project settings > fabricator > pIecemarking > | clip configurations | top
| Each bolt diameter is a distinct clip angle configuration. The tabs show imperial sizes when the " Available bolt diameters " is ' Imperial '. Metric sizes are shown when the " Available bolt diameters " is ' Metric '. If " Available bolt diameters " is set to ' Both ', the primary dimensioning " Units " set whether the tabs show imperial or metric bolt sizes. |
Standard angle size: The angle section size for the specific bolt diameter tab that has been selected. The angle specified here must also be listed in the local shape file .
Attach long leg to: Supported or Supporting . This applies when a " Standard angle size " with unequal legs has been entered (for example, the long leg for L3 1/2x3x5/16 angle material is the leg that is 3 1 /2 inches in length). In a typical situation where a beam frames into a column, the supported member is the beam.
Hole type in leg to supported member: Standard round or Short slot or Long slot or Oversized or User Slot #1 or User Slot #2 .
Effect on a full-featured SDS2 program: The hole type shown here applies to the clip angle leg that attaches to the supported beam web. A full-featured SDS2 program determines the specific size of a hole based on the " Hole type . . . " shown here and the bolt diameter that is selected as the tab.
Gage on leg to supported member: The distance (in the primary dimension " Units " or in other units ) from the outside corner of the clip angle to the center of the column of holes on the leg that bolts to the supported beam.
Hole type in leg to supporting member: Standard round or Short slot or Long slot or Oversized or User slot #1 or User slot #2 .
Effect on a full-featured SDS2 program: The hole type shown here applies to the clip angle leg that attaches to the supporting beam or column.
Use gage on leg to supporting member for: 
Slots only or All hole types .
'
'
Gage on leg to supporting member: The distance (in the primary dimension " Units " or other units ) from the outside corner of the clip angle to the center of the column of slots on the outstanding leg (on the leg that bolts to the supporting beam or column).
For slots only, in a full-featured SDS2 program connection design may apply a different GOL than that which is entered here in order to permit the bolts to fit in the slots at the " Narrow gage " center-to-center hole distance.
Begin staggered bolt pattern at bolt diameter: The minimum bolt diameter (in the primary dimension " Units " or in other units ) at which bolt patterns are to be staggered when a full-featured SDS2 program designs a clip angle connection.
home > project settings > fabricator > pIecemarking > | clip configurations | top
------ Clip angle piecemarks ------
Column heads (GOLs): Each column head on this table is a GOL (gage on outstanding leg). These GOLs are calculated from the " Narrow gage " center-to-center hole distance that is entered in Clip Angle Settings .
Rows: Each row on the Clip Angle Piecemarks table is a number of rows of bolts.
Number of rows = ' 3 ' Effect on a full-featured SDS2 program: Submaterial piecemarks shown here will be assigned in a full-featured SDS2 program to bolted narrow gage clip angles according the gage on the outstanding leg and number of rows of bolts designated on this table.
home > project settings > fabricator > pIecemarking > | clip configurations | top