The Continuous Footing Template Editor
- A template that you create/edit in the Continuous Footing Template Editor window can be entered to " Template " on the Continuous Footing Edit window.
 |
To open this window , double-click a template on the Continuous Footing Templates window, or on that same window select a template and press " Edit " or press " Add ." One :" Template item " (a profile) should always be shown. To add an item to that profile, press the " Add " button. To delete an item, select it and press the " Erase " button. Select a " Template Item " to edit that item. |
opens a window with a list of template items that you can add to the " Template items " list shown above. In order to select " Tie ," you need to first have a bar pattern already on the list of " Template Items ."
Grid cont bar pattern
After pressing " Add " then selecting " Tie ," you select the item's shape (its picture), then you are prompted to select the perimeter reinforcing bars that you want the tie to constrain. It is permissible to select the same bar twice. The dimensions of the tie are based on the bars that you select.
The black pointers in this example point to the bars that were selected in order to create the green tie . The remaining bars (those not marked with pointers) were selected when the orange tie was created. To place the green tie above the orange tie, the user entered a " Depth offset " for the green tie that was equal to the green tie's diameter.
deletes the item on the " Template Items " list that you have selected. Be aware that you cannot delete a profile. The " Erase " button is disabled -- grayed out -- when the item selected under " Template Items " is a profile. See " Profile ."
"OK" (or the Enter key) closes the Continuous Footing Template Editor and reactivates the Continuous Footing Templates window. The template edited using this window will be saved to the Job Settings file in your current Job . To apply template changes to a continuous footing that uses that template in the model, you can mark that the continuous footing to which the template was added for processing then Process and Create Solids .
"Cancel" (or the Esc key or the
button) closes this window without saving any changes made to it.
"Reset" undoes all changes made to this window since you first opened it. The window remains open.
page 1 | concrete footing templates | top
"""" Name and End Cover :
Name: Read only or Blank . The name of the continuous footing template that you are adding or editing.
If " Name " is read-only , this is the name of the " Template " that you selected on the Continuous Footing Templates window when you opened this window. It is the name of the template that you are editing.
If " Name " is blank , then you pressed " Add " to open this window, You must type a " Name " in order to complete the creation of the new template.
Tip: If you want to change the name of a template, you can create a template exactly like that template but with the new name that you want. Just select that template (on the Continuous Footing Templates window, not this window) then press " Save As ."
End cover: The distance (in the primary dimension " Units " or other units ) from the left end of the rebar in the left-end member of a continuous footing layout to the left-end edge of that same member. This " End cover " distance also applies to the right end of the right-end footing in a continuous footing layout.
|
An elevation view of one end of a continuous footing. The " End cover " distance sets back the reinforcing bars at each end of a layout. Intermediate footings in a layout have corner splices. |
The following options can be found in various Template Items "" :
Profile: Rectangular or Custom . This applies when the item selected on the " Templates item " list is a profile. A profile viewed in the Continuous Footing Template Editor shows a perspective from the left end of the footing. A continuous footing's left end is established by the 1st work point that was located when that member was added.
' Rectangular ' gives you options for defining a rectangular or square profile, including a cover. See " Concrete Profile (Rectangular) ."
' Custom ' gives you options for a profile that is a shape that you define by pressing " Edit ." There are no options for defining a cover. See " Concrete Profile (Custom) ."
Rebar size: Any size that has been entered to the Rebar Definitions Setup window under the " Active rebar standard " can be selected here.
A " Rebar size " must be selected for a " Cont bar pattern (Grid) " or " Cont bar pattern (Single) " or " Cont bar pattern (Perimeter) " or " Tie definition "
User configuration: If a size that you want is not available, you can add that size on the Rebar Definitions Setup window.
Standard: Any standard that has been entered to the Rebar Specifications window can be selected here.
A " Standard " must be selected for a " Cont bar pattern (Grid) " or " Cont bar pattern (Single) " or " Cont bar pattern (Perimeter) " or " Tie definition "
User configuration: If a standard that you want is not available, you can add that standard on the Rebar Specifications window.
Steel grade: Any steel grade that is available in the " Standard " that you have selected can be selected here.
A " Steel grade " must be selected for a " Cont bar pattern (Grid) " or " Cont bar pattern (Single) " or " Cont bar pattern (Perimeter) " or " Tie definition "
User configuration: If a steel grade is not available for selection, selecting a different " Standard " will make that steel grade available if the steel grade you want is in that other standard. If you don't want to change to a different " Standard ," you can open the Rebar Specifications window and add the steel grade you want to the standard that you currently have selected.
Coating: None or a Coating that is available in the " Standard " that you have selected. A " Coating " can be selected for a " Cont bar pattern (Grid) " or " Cont bar pattern (Single) " or " Cont bar pattern (Perimeter) " or " Tie definition "
Select ' None ' if you do not want a coating. Since it is possible to create standards that do not have coatings, it is possible that ' None ' may be your only option.
User configuration: If a coating is not available for selection, selecting a different " Standard " will make that coating available if the coating you want is in that other standard. If you don't want to change to a different " Standard ," you can open the Rebar Specifications window and add the coating you want to the standard that you currently have selected.
Function: Any usage description from the " Grade Beam / Continuous Footing " section of the Rebar Usage Descriptions window. The " Function " that you enter here is used on rebar schedules to identify continuous bars.
A " Function " can be selected for a " Cont bar pattern (Grid) " or " Cont bar pattern (Single) " or " Cont bar pattern (Perimeter) " or " Tie definition "
User configuration: To add a " Function " that you can select here, you can type that function to the " Grade Beam / Continuous Footing " section of the Rebar Usage Descriptions window.
Corner Function: Any usage description from the " Grade Beam / Continuous Footing " section of the Rebar Usage Descriptions window. The " Function " that you enter here is used on rebar schedules to identify corner bars.
A " Corner Function " can be selected for a " Cont bar pattern (Grid) " or " Cont bar pattern (Single) " or " Cont bar pattern (Perimeter) ."
User configuration: To add a " Function " that you can select here, you can type that function to the " Grade Beam / Continuous Footing " section of the Rebar Usage Descriptions window.
When this box is checked (
), a grid with X-axis and Y-axis rulers overlays the depiction of the template.
When the box is not checked (
), the template is depicted without the grid overlay.
page 1 | concrete footing templates | top
------ Concrete Profile (Rectangular) ------
Width: A distance (in the primary dimension " Units " or other units ). When a grade beam in Modeling that has this template's " Name " entered to " Template " on its Grade Beam Edit window, then the " Width " entered here is the actual cross-sectional width of that grade beam.
|
In Modeling , the " Width " of the grade beam's cross section is horizontal across your computer screen if you are looking at an elevation view of either end of the member. |
Height: A distance (in the primary dimension " Units " or other units ). When a grade beam in Modeling that has this template's " Name " entered to " Template " on its Grade Beam Edit window, then the " Height " entered here is the actual cross-sectional height of that grade beam.
|
|
In Modeling , the " Height " of the grade beam's cross section is vertical across your computer screen if you are looking at an elevation view of either end of the member. |
When this box is checked (
When the box is not checked (
Top cover: The concrete thickness (in the primary dimension " Units " or other units ) of the continuous footing's top cover.
|
In Modeling , the top cover of a continuous footing's cross section matches the rectangular profile shown in the Continuous Footing Template Editor regardless of how you locate your points. Top is always the higher elevation. |
Bottom cover: The concrete thickness (in the primary dimension " Units " or other units ) of the continuous footing's bottom cover.
|
|
In Modeling , the bottom cover of a grade beam's cross section matches the rectangular profile shown in the Continuous Footing Template Editor regardless of how you locate your points. Bottom is always the lower elevation. |
Left cover: The concrete thickness (in the primary dimension " Units " or other units ) of the continuous footing's left cover.
|
|
In Modeling , the left cover of a grade beam's cross section matches the rectangular profile shown in the Continuous Footing Template Editor if you are looking at the end where the 1st work point was located (the left end). If you're looking from the 2nd work point, then the left cover will be on your right. |
Right cover: The concrete thickness (in the primary dimension " Units " or other units ) of the continuous footing's right cover.
|
|
In Modeling , the right cover of a grade beam's cross section matches the rectangular profile shown in the Continuous Footing Template Editor if you are looking at the end where the 1st work point was located (the left end). If you're looking from the 2nd work point, then the right cover will be on your left. |
page 1 | concrete footing templates | top
------ Concrete Profile (Custom) ------
|
| When the " Profile " is set to ' Custom ', pressing the " Edit " button opens the Co ncrete Profile window, which you can use to edit the profile as described below. |
|
Radius: A distance (in the primary dimension " Units " or other units ) that defines the amount of corner rounding that takes place.
The " Radius " is the radius of a circle. Two lines that are tangent to that circle meet at the located point. The corner's arc ends at the points of tangency of these two lines. 
A " Radius " of ' 0 ' designates a sharp corner with no corner rounding.
Increasing the size of the " Radius " moves the edge of the rounded corner back from the corner point. This is because the " Radius " defines a circle that is tangent to both lines to the corner point. The arc of the rounded corner begins and ends at the tangent points.
You can set a different " Radius " for each corner. Clicking on the upper-right corner of the table (" Radius > ") lets you set the radius for each point to be the same value.
page 1 | concrete footing templates | top
------ Continuous bar pattern (Perimeter) ------
page 1 | concrete footing templates | top
------ Continuous bar pattern (Grid) ------
Snap to cover: A Top and/or Bottom and/or Left and/or Right perimeter constraint to the pattern. The option applies when the profile is rectangular. The option is disabled ( grayed out ) when the " Profile " is ' Custom '. Be aware that when bars snap to the cover the initial placement of those bars is readjusted to compensate for the thickness of the tie when you " Add " a tie.
Top:
Bottom:
Left:
Right:
Tip: Since " Row spacing " and " Columns spacing " are center-to-center spacings, the math needed to calculate how to use those options to place continuous bars flush with the cover could be tedious. Its usually easier to use these snaps and let Continuous Footing Template Editor calculate the needed spacing for you.
Center location: An X distance and a Y distance from the center, top of the profile. Distances can be entered in the primary dimension " Units " or other units .
"X" is the X distance and can be positive or negative. A value of 0 aligns the horizontal center of the pattern at the horizontal center of the profile. Entering a negative X distance moves the horizontal center of the pattern that distance to the left. Entering a positive X distance moves the horizontal center of the pattern that distance to the right.
"Y" is the Y distance and can be positive or negative. A value of 0 aligns the vertical center of the pattern with the top of the profile. A value of -h/2 aligns the vertical center of the pattern at the center of the profile, where h is the " Height " of a rectangular profile. Entering a negative Y distance moves the vertical center of the pattern down. Entering a positive Y distance moves the vertical center of the pattern up.
# rows: The total count (an integer) of continuous bar rows in the grid pattern. Rows run horizontally in the pattern. The " Spacing " between rows runs vertically.
Spacing (rows): The center-to-center distance between rows of continuous bars in the grid pattern. Rows run horizontally in the pattern. The " Spacing " between rows runs vertically.
# columns: The total count (an integer) of continuous bar columns in the grid pattern. Columns run vertically in the pattern. The " Spacing " between columns runs horizontally.
Spacing (columns): The center-to-center distance between columns of continuous bars in the grid pattern. Columns run vertically in the pattern. The " Spacing " between columns runs horizontally.
page 1 | concrete footing templates | top
------ Continuous bar pattern (Single) ------
Center location: A positive or negative X distance and Y distance from the center, top of the profile. Distances can be entered in the primary dimension " Units " or other units .
"X" can be positive or negative. A value of 0 centers the continuous bar at the horizontal center of the profile. Entering a negative X distance moves the continuous bar that distance to the left. Entering a positive X distance moves the continuous bar that distance to the right.
"Y" can be positive or negative. A value of 0 aligns the vertical center of the continuous bar with the top of the profile. A value of -h/2 aligns the vertical center of the continuous bar at the center of the profile, where h is the " Height " of a rectangular profile. Entering a negative Y distance moves the continuous bar down. Entering a positive Y distance moves the continuous bar up.
page 1 | concrete footing templates | top
This is the tie definition shape that you selected after you pressed " Add " and selected " Tie ."
-To change this shape, you need to select this " Template item " then press " Erase " then press " Add " and select " Tie " and then select a different shape.
Depth offset: A positive or negative distance . This places the left-most tie with respect to the left end of the longitudinal continuous bars. Subsequent ties are placed based on their " Spacing ." Distances can be entered in the primary dimension " Units " or other units . A continuous footing's left end is established by the 1st work point that was located when that member was added. As shown in the example below, you might use the " Depth offset " to prevent ties from clashing when you have defined multiple ties in a template.
|
#3 rebar is used for both ties in this example. A " Depth offset " of ' 3/8 ' was entered to keep the two ties from clashing. |
' 0 ' places the left-most tie 1 inch from the left end of the longitudinal continuous bars.
' A positive distance ' displaces the left-most tie that distance from its zero position in the direction of the left end.
' A negative distance ' displaces the left-most tie that distance from its zero position in the direction of the right end.
Spacing: The distance between ties. Distances can be entered in the primary dimension " Units " or other units .
page 1 | concrete footing templates | top
To close/reset the Continuous Footing Template Editor :
"OK" (or the Enter key) closes the Continuous Footing Template Editor and reactivates the Continuous Footing Templates window. The template edited using this window is saved to the Job Settings file in your current Job . To apply template changes to a continuous footing that uses that template in the model, you can to mark for processing that continuous footing then Process and Create Solids .
"Cancel" (or the Esc key or the
"Reset" undoes all changes made to this window since you first opened it. The window remains open.
Also see :
- Continuous Footing Templates (the Continuous Footing Template Editor is opened from)
- Continuous Footing Edit (window for editing continuous footings in Modeling )
page 1 | concrete footing templates | top