" 
Brace Connection To Gusset Hss Paddle " connection design locks
| A paddle plate end fitting on an HSS, pipe or tube vertical brace to a shared gusset on a column is designed per " Brace Connection To Gusset Hss Paddle " locks when ' Paddle plate ' is the selected " Pipe/tube end-fitting ."
|
|
|||||
| " Brace Connection To Gusset Hss Paddle "
(paddle plate on an HSS, pipe or tube brace)  |
" Brace Connection To Gusset Hss Paddle "
(hole pattern for field bolts)  |
||||
|
|||||
) (HSS/TS)
User Defined Connections: Settings that are locked (
) in the user defined connection file will automatically be locked on the member edit window. You can, if you so choose, manually lock additional settings on the member edit window, and your changes will be retained, through multiple processes, so long as you do not change to a different connection then switch back to the original user defined connection.
Vertical Brace Edit: To change a setting, first set it to locked (
) may be updated, and the "
user defined | vertical brace edit | top
Connection design locks :
| Locks not dimensioned or called out on the drawing are marked ( not depicted ). |
Brace Connection To Gusset Hss Paddle
( 2- or 3-point, to a column )
Paddle Plate
Width: The distance between the two corners of the forward edge of the paddle plate. The width of the plate is perpendicular to the work line of the vertical brace. See example .
Length: The length of either of the two edges of the paddle plate that are parallel with the work line of the vertical brace. Increasing the " Length " extends the plate toward the opposite end of the vertical brace. The length of the weld and the " Notch length " in the vertical brace main material are updated automatically. See example .
Thickness ( not depicted ): The distance between the near side and far side faces of the paddle plate. Since the thickness of the paddle plate is centered with respect to the work line of the vertical brace, increasing the " Thickness " adds material to both sides of the work line. The weld placement and " Notch width " in the vertical brace main material are updated automatically.
End connection failure message: Paddle plate won't fit inside HSS brace
Refx: The distance from the end of the paddle plate to the work point of the brace. Tip: To get a properly designed connection, the " Minus dimension " ( "
Refy ( rfy ): The distance from the work line of the vertical brace to the length edge of the paddle plate (the length edge is parallel with the work line). This distance is perpendicular with the work line of the vertical brace and in the same plane as the paddle plate. Changing the " Refy " slides the paddle plate sideways, perpendicular to the work line -- it does not move the holes in the plate since hole placement is set on the gusset plate. See example .
Paddle Plate To Gusset Connection
Bolt diameter ( not depicted ): You can either type in any diameter (inches or mm), or you can select a bolt diameter from the combo box (
). The diameters that are listed in the combo box come from Home > Project Settings > Job > Bolt Settings > the " Available bolts " list. The bolt diameter entered here, together with the " Hole type " entered below, set the diameter of holes the bolts go into.
Hole type ( not depicted ): Standard round or Short slot or Oversized or Long slot or User slot #1 or User slot #2 . The hole type selected here, together with the " Bolt diameter " entered above, set the diameter of holes for field bolting the supported brace to the half of the gusset plate you are editing.
Rows: The number of holes in any one column of holes. Bolt rows run parallel with the work line of the vertical brace (see example ). For a ' Paddle plate ' end fitting, these holes are for field bolting the plate to the gusset. Entering ' 0 ' removes the holes. For the brace in the example above, the number of " Rows " is ' 5 '.
Distance to 1st hole along brace ( to 1st hole ): The positive distance (parallel with the work line of the vertical brace) from the work point to the center of the nearest hole (see example ).
Hole spacing along brace ( rs ): Row spacing. This is the distance (center to center) between of any two adjacent holes in the same column of holes (see example ).Bolt row spacing runs parallel with the work line of the vertical brace.
End connection failure message: Invalid bolt spacing
Edge distance along brace ( ed ): The distance from the forward edge of the paddle plate to the nearest hole in the paddle plate (see example ). The forward edge is the paddle plate edge that is closest to the work point of the HSS vertical brace. Holes in the paddle plate are for field bolting the paddle plate to the gusset plate.
Other edge distance along brace ( oed ): The distance from the edge of the gusset plate to the nearest hole for field bolting the paddle plate to the gusset plate (see example ).
Columns: The number of columns of holes in the half of the gusset that is being edited. For a ' Paddle plate ' end fitting, these holes are for field bolting the plate to the gusset. In the example above, the number of " Columns " is ' 2 '. Bolt column spacing runs perpendicular to the work line of the vertical brace.
Distance to 1st hole perpendicular to brace ( perp ): The distance from the work line of the vertical brace perpendicular to the nearest column of holes. In the example above, this distance would be half the " Hole spacing perpendicular to brace " since the two columns of holes are centered around the work line of the brace.
Hole spacing perpendicular to brace ( cs ): Column spacing. This is the distance (center to center) between any two adjacent columns of holes in the half of the gusset being edited (see example ). Bolt column spacing runs perpendicular to the work line of the vertical brace.
Horizontal edge distance ( hed ): The distance (perpendicular to the work line of the vertical brace) from the length edge of the paddle plate to the nearest column of holes for field bolting the paddle plate to the gusset plate. See the example .